Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.

Don't underestimate the forklift at the workplace. If the procedure is not good, there will be severe crashes in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the driver's sight, and the person in front could not be found, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must take note of these matters ：.

Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that hinder the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift begins with a load, the motorist must initially verify that the lots is stable and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will affect the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are special situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load will not be elevated other than when piling or filling. .
8. The elevation of the tons should not block the chauffeur's sight. In special conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the load, and it must be noted that the fork tip must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not slide in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter Stand-on Electric Pallet Stacker a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no Stand-on Electric Pallet Stacker switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844